Výsledky vyhľadávania
Názov Granulometric composition of chips and dust produced from the process of working thermally modified wood Aut.údaje Alena Očkajová ... [et al.] Autor Očkajová Alena 1961- (35%) UMBFP07 - Katedra techniky a technológií
Spoluautori Kučerka Martin 1980- (35%) UMBFP07 - Katedra techniky a technológií
Kminiak Richard (20%)
Rogoziński Tomasz (10%)
Zdroj.dok. Acta Facultatis Xylologiae Zvolen. Roč. 62, č. 1 (2020), s. 103-111. - Zvolen : Technická univerzita vo Zvolene, 2020 Kľúč.slová woodworking drevo - wood granulometric analysis Form.deskr. články - journal articles Jazyk dok. angličtina Krajina Slovenská republika Anotácia The granulometric composition of chips and dust from the longitudinal milling and sanding of thermally modified oak and spruce wood over a set of modification temperatures: 160, 180, 200 and 220 °C is determined and differences between the factors affecting the granulometry during these two woodworking processes are defined in the paper. Sieve analysis yielded percentages on individual sieves. Residual curves were used to emphasize the difference in these technologies in the granulometric composition, where a shift to the left signals smaller (finer particles) or dust particles. While the sanding dust residue curves shift to the right due to the elevated temperature of the wood treatment, i.e. towards larger fine particles and medium coarse particles, the chip residue curves from the milling process shift to the left, with a higher share of medium coarse, fine and dust fractions due as the wood modification temperature increases URL Link na zdrojový dokument Kategória publikačnej činnosti ADN Číslo archívnej kópie 47585 Kategória ohlasu CHUCHALA, Daniel - SANDAK, Jakub - ORLOWSKI, Kazimierz A. - MUZINSKI, Tomasz - LACKOWSKI, Marcin - OCHRYMIUK, Tomasz. Effect of the drying method of pine and beech wood on fracture toughness and shear yield stress. In Materials. ISSN 1996-1944, 2020, vol. 13, no. 20, pp. 1-17.
CANDELIER, Kevin - DIBDIAKOVA, Janka. A review on life cycle assessments of thermally modified wood. In Holzforschung. ISSN 0018-3830, 2021, vol. 75, no. 3, pp. 199-224.
RAJKO, Lubomir - KOLEDA, Peter - BARCIK, Stefan - KOLEDA, Pavol. Technical and technological factors' effects on quality of the machined surface and energetic efficiency when planar milling heat-treated meranti wood. In BioResources. ISSN 1930-2126, 2021, vol. 16, no. 4, pp. 7884-7900.
CUI, Yunqi - YIN, Jian - CAI, Yitong - WANG, Huimin - ZHU, Nanfeng - DING, Tao. Spatial distribution characteristics of the dust emitted at different cutting speeds during MDF milling by image analysis. In Journal of wood science. ISSN 1435-0211, 2022, vol. 68, no. 1, pp. 1-13.
REH, Roman - KRISTAK, Lubos - ANTOV, Petar. Advanced eco-friendly wood-based composites. In Materials. ISSN 1996-1944, 2022, vol. 15, no. 23, pp. 1-5.
SATINOVA, Viktoria - HLAVAC, Pavol - IZDINSKY, Jan - REINPRECHT, Ladislav. Rot evaluation in spruce logs and rot reflection into dimensions of chips for particleboards. In Acta Facultatis xylologiae Zvolen. ISSN 1336-3824, 2022, vol. 64, no. 2, pp. 5-16.
DZURENDA, Ladislav - BANSKI, Adrián. Chip grain size from the process of machining steamed and unsteamed alder wood on a cnc machining center and assessment of separation results. In Annals of Warsaw university of life sciences SGGW : forestry and wood technology. ISSN 1898-5912, 2023, no. 121, pp. 43-50.
Katal.org. BB301 - Univerzitná knižnica Univerzity Mateja Bela v Banskej Bystrici Báza dát xpca - PUBLIKAČNÁ ČINNOSŤ Odkazy PERIODIKÁ-Súborný záznam periodika Názov Granulometric analysis of sanding dust from selected wood species Aut.údaje Alena Očkajová, Martin Kučerka ... [et al.] Autor Očkajová Alena 1961- (58%) UMBFP07 - Katedra techniky a technológií
Spoluautori Kučerka Martin 1980- (14%) UMBFP07 - Katedra techniky a technológií
Krišťák Ľuboš (14%)
Igaz Rastislav (14%)
Zdroj.dok. BioResources. Vol. 13, no. 4 (2018), pp. 7481-7495. - Raleigh : North Carolina State University, 2018 Kľúč.slová wood dust granulometric analysis granularity Jazyk dok. slovenčina Krajina Spojené štáty Systematika 62 Anotácia Different types of sanders are used in every furniture and carpentry plant. The wood dust generated during sanding is considered one of the main health and safety hazards. The greatest danger to respiratory organs is a respirable (alveolar) component with a particle size of less than 10 μm. Thus, it is important to know the specific particle size fractions of wood dust. This study compared the granulometric compositions of abrasion wood dusts of selected wood species (beech and oak) and determined the statistical significance of individual factors (type of sander, wood species, grain size of sander, sanding direction) that affect the percentage of fractions ≤ 0.08 mm. The results confirmed that the use of narrow band and handheld (belt and disc) sanders caused high percentages of fractions ≤ 0.08 mm, above 90% in all cases. In these types of sanders, the working part of the sander is not completely covered, and the operator is in direct contact with the machine. Despite the use of a suction device, a certain amount of dust remains suspended in the air, or it settles on surfaces. In both cases, this dust poses a health and safety hazard URL Link na plný text Kategória publikačnej činnosti ADC Číslo archívnej kópie 42672 Kategória ohlasu KMINIAK, Richard - DZURENDA, Ladislav. Impact of sycamore maple thermal treatment on a granulometric composition of chips obtained due to processing on a CNC machining mentre. In Sustainability. ISSN 2071-1050, 2019, vol. 11, no. 3, pp. 1-10.
KMINIAK, Richard - DZURENDA, Ladislav. Granulometric composition of chips from the milling process of spruce on a CNC machining center. In Annals of Warsaw University of life sciences - SGGW (Forestry and Wood Technology). ISSN 1898-5912, 2018, no. 104, pp. 48-52.
MOJŽIŠ, Miroslav - BUBENÍKOVÁ, Tatiana - ZACHAR, Martin - KACIKOVÁ, Danica - STEFKOVÁ, Jaroslava. Comparison of natural and synthetic sorbents' efficiency at oil spill removal. In BioResources . ISSN 1930-2126, 2019, vol. 14, no. 4, pp. 8738-8752.
VANDLIČKOVÁ, Miroslava - MARKOVÁ, Iveta - MAKOVICKÁ-OSVALDOVÁ, Linda - GAŠPERCOVÁ, Stanislava - SVETLÍK, Jozef. Evaluation of African Padauk (Pterocarpus soyauxii) explosion dust. In BioResources. ISSN 1930-2126, 2020, vol. 15, no. 1, pp. 401-414.
DADO, Miroslav - MIKUŠOVÁ, Lucia - SCHWARZ, Marian - HNILICA, Richard. Effect of selected factors on mass concentration of airborne dust during wood sanding. In MM Science journal. ISSN 1803-1269, 2019, vol. 2019, pp. 3679-3682.
VANDLIČKOVÁ, Miroslava - MARKOVÁ, Iveta. Ignition of wood dust of African Padauk (Pterocarpus Soyauxii). In International scientific conference on woods and fire safety. Springer : Cham, 2020. ISBN 978-3-030-41234-0, pp. [1-4].
VANDLIČKOVÁ, Miroslava - MARKOVÁ, Iveta - OSVALDOVÁ, Linda Makovicka - GAŠPERCOVÁ, Stanislava - SVETLÍK, Jozef - VRANIAK, Jozef. Tropical wood dusts-granulometry, morfology and ignition temperature. In Applied sciences. ISSN 2076-3417, 2020, vol. 10, no. 21, pp. 1-15.
PEDZIK, Marta - STUPER-SZABLEWSKA, Kinga - SYDOR, Maciej - ROGOZINSKI, Tomasz. Influence of grit size and wood species on the granularity of dust particles during sanding. In Applied sciences. ISSN 2076-3417, 2020, vol. 10, no. 22, pp. 1-9.
ROGOZINSKI, Tomasz - CHUCHALA, Daniel - PEDZIK, Marta - ORLOWSKI, Kazimierz A. - DZURENDA, Ladislav - MUZINSKI, Tomasz. Influence of drying mode and feed per tooth rate on the fine dust creation in pine and beech sawing on a mini sash gang saw. In European journal of wood and wood products. ISSN 0018-3768, 2021, vol. 79, no. 1, pp. 91-99.
KWIDZINSKI, Zdzislaw - BEDNARZ, Joanna - PEDZIK, Marta - SANKIEWICZ, Lukasz - SZAROWSKI, Piotr - KNITOWSKI, Bartlomiej - ROGOZINSKI, Tomasz. Innovative line for door production technoPORTA - technological and economic aspects of application of wood-based materials. In Applied sciences. ISSN 2076-3417, 2021, vol. 11, no. 10, art. no. 4502, pp. 1-20.
SYDOR, Maciej - MIRSKI, Radoslaw - STUPER-SZABLEWSKA, Kinga - ROGOZINSKI, Tomasz. Efficiency of machine sanding of wood. In Applied sciences. ISSN 2076-3417, 2021, vol. 11, no. 6, art. no. 2860, pp. 1-12.
VANDLIČKOVÁ, Miroslava - MARKOVÁ, Iveta - HOLLÁ, Katarína - GAŠPERCOVÁ, Stanislava. Evaluation of marblewood dust's (Marmaroxylon racemosum) effect on ignition risk. In Applied sciences - Basel. ISSN 2076-3417, 2021, vol. 11, no. 15, art. no. 6874, pp. 1-9.
GEJDOŠ, Miloš - LIESKOVSKÝ, Martin. Selected risks in the storage of biomass in heating plants of urban-type : Slovakian case study. In WoodEMA 2021 : the response of the forest-based sector to changes in the global economy : 14th international scientific conference, Koper, 16th-18th June 2021. Zagreb : WoodEMA - International association for economics and management in wood processing and furniture manufacturing, 2021. ISBN 978-961614441-4, pp. 399-404.
MRAČKOVÁ, Eva - SCHMIDTOVÁ, Jarmila - KMEŤOVÁ, Elena - KAČÍKOVÁ, Danica. Granulometric analysis of spruce wood dust. In Delta (Zvolen). ISSN 1337-0863, 2021, vol. 15, no. 1, pp. 50-57.
DEMBINSKI, Czeslaw - POTOK, Zbigniew - DOLNY, Stanislaw - KMINIAK, Richard - ROGOZINSKI, Tomasz. Performance of filter bags used in industrial pulse-jet baghouses in wood-based panels furniture factory. In Applied sciences (Basel). ISSN 2076-3417, 2021, vol. 11, no. 19, pp. 1-15.
VANDLÍČKOVÁ, Miroslava - MARKOVÁ, Iveta - GAŠPERCOVÁ, Stanislava - HOLLÁ, Katarína. Effect of particle size distribution of cumar dust on risk of initiation. In Waste forum. ISSN 1804-0195, 2021, no. 4, pp. 273-285.
GALLO, Pietro - FAILLA, Sabina - BIOCCA, Marcello - PARIS, Enrico - GALLUCCI, Francesco - FORNACIARI, Laura - SCHILLACI, Giampaolo. Exposure to heavy metals in wood dust during dry-pruning in vineyard. In Lecture notes in civil engineering : 06th international conference on safety, health and welfare in agriculture and agro-food systems (SHWA 2021), online, 15th-18th September 2021. ISSN 2366-2557, 2022, vol. 252 LNCE, pp. 207-215.
TUREKOVA, Ivana - MARKOVA, Iveta - SVENTEKOVA, Eva - HARANGOZO, Jozef. Evaluation of microclimatic conditions during the teaching process in selected school premises. Slovak case study. In Energy. ISSN 0360-5442, 2022, vol. 239, part D, art. no. 122161, pp. 1-8.
RATNASINGAM, Jegatheswaran. Sanding process. In Furniture manufacturing : a production engineering approach. Singapore : Springer Singapore, 2022. ISBN 978-981-16-9411-0, pp. 79-88.
CUI, Yunqi - YIN, Jian - CAI, Yitong - WANG, Huimin - DING, Tao - ZHU, Nanfeng. Morphological characteristics of bamboo panel milling dust derived from different average chip thicknesses. In Forests. ISSN 1999-4907, 2022, vol. 13, no. 9, pp. 1-18.
DADO, Miroslav - SALVA, Jozef - SCHWARZ, Marian - VANEK, Miroslav - BUSTIN, Lucia. Effect of grit size on airborne particle concentration and size distribution during oak wood sanding. In Applied sciences (Basel). ISSN 2076-34717, 2022, vol. 12, no. 15, pp. 1-14.
ZHOU, Xihe - LI, Xiaoxu - CUI, Zhongwen - WU, Lin - ZHOU, Handong - LU, Xiaoning. Combustible wood dust explosions and impacts on environments and health - a review. In Environmental research. ISSN 0013-9351, 2023, vol. 216, art. no. 114658, pp. 1-17.
PONPRATHOM, Yothin. Design and development of protective equipment from noise and dustof circular saws. In Advanced science journal. ISSN 1513-9980, 2022, vol. 22, no. 2, pp. R1-R20.
KOLEDA, Pavol - KOLEDA, Peter - HRČKOVÁ, Mária - JÚDA, Martin - HORTOBÁGYI, Áron. Experimental granulometric characterization of wood particles from CNC machining of chipboard. In Applied sciences. ISSN 2076-3417, 2023, vol. 13, no. 9, pp. 1-15.
BIOCCA, Marcello - POCHI, Daniele - GALLO, Pietro - FANIGLIULO, Roberto. Air-borne particle size distribution of wood dust emitted during small scale forestry operations. In Journal of basic and applied sciences [online]. 2023, vol. 19, pp. 60-67 [cit. 2023-09-06]. ISSN 1927-5129. Dostupné na: https://doi.org/10.29169/1927-5129.2023.19.05
SHER, Farooq - BOŠKAILO, Emina - SMJEČANIN, Narcisa - NEMȚANU, Monica R. - SHER, Emina K. - LIMA, Eder C. Magnetic multifunctional nanomaterials for enhanced transverse chemical and bioanalytical applications - a review. In TrAC trends in analytical chemistry. ISSN 0165-9936, 2024, vol. 173, art. no. 117622, pp. 1-19.
Katal.org. BB301 - Univerzitná knižnica Univerzity Mateja Bela v Banskej Bystrici Báza dát xpca - PUBLIKAČNÁ ČINNOSŤ Odkazy PERIODIKÁ-Súborný záznam periodika Názov Wood dust risk assessment by granulometry of selected wood dust Aut.údaje Iveta Marková, Alena Očkajová, Jana Jaďuďová Autor Marková Iveta 1971- (60%) UMBFP04 - Katedra životného prostredia
Spoluautori Očkajová Alena 1961- (20%) UMBFP07 - Katedra techniky a technológií
Jaďuďová Jana 1983- (20%) UMBFP04 - Katedra životného prostredia
Zdroj.dok. Zbornik radova : 5. meždunarodna naučna konferencija "Bezednosni inženering" : 15. medunarodna konferencija "Zaštite od požara i eksplozije", Novi Sad, 05. - 07. okťjabr 2016. S. 80-89. - Novi Sad : Visoka technička škola strukovnich studija v Novom Sadu, 2016 ; Safety engineering medzinárodná vedecká konferencia ; Fire and explosion protection medzinárodná vedecká konferencia Kľúč.slová wood dust orbital sander granulometric analysis Jazyk dok. angličtina Krajina RS Systematika 502 Kategória publikačnej činnosti BEE Číslo archívnej kópie 37289 Katal.org. BB301 - Univerzitná knižnica Univerzity Mateja Bela v Banskej Bystrici Báza dát xpca - PUBLIKAČNÁ ČINNOSŤ Odkazy (1) - PUBLIKAČNÁ ČINNOSŤ Názov Granulometry of selected wood dust species of dust from orbital sanders Aut.údaje Iveta Marková ... [et al.] Autor Marková Iveta 1971- (40%) UMBFP04 - Katedra životného prostredia
Spoluautori Mračková Eva (30%)
Očkajová Alena 1961- (20%) UMBFP07 - Katedra techniky a technológií
Ladomerský Juraj 1948- (10%)
Zdroj.dok. Wood Research. Roč. 61, č. 6 (2016), s. 983-992. - Bratislava : Výskumný ústav papiera a celulózy, Slovenský drevársky výskumný ústav, 2016 Kľúč.slová drevný prach granulometria wood dust granulometric analysis Jazyk dok. angličtina Krajina Slovenská republika Systematika 67/68 Anotácia Formation and presence of dust in the timber premises is part of the technology. Dust is generated as a byproduct based on the method of machining. The paper deals with granulometric analysis of selected samples of wood dust sessile oak (Quercus petraea Liebl.) and from deciduous multiple-pore wood there was chosen European beech (Fagus sylvatica L.) and alder (Alnus glutinosa L.) and the mixture taken directly from timber production of grinders SCM SANDYA 300RCS) for the purpose of selecting the percentages of the various fractions (0.032; 0.063; 00:08; 0.125; 0.250; 0.5; 1; 2 mm) of samples of wood dust. Wood dust samples were made using a hand orbital sander BOSCH PSS 200AC and sizing on the automatic mesh vibratory sieve machine Retsch AS 200 control. The most frequent percentages of dust particles (between 50-79 %) in all samples of wood dust there were fractions of 32 and less than 32 mu m (bottom). The most abundant percentage creates conditions of the risk of inhaling and respirable components contained in the fraction over 32 mu m and the potential of formation of a dust-air explosive mixture. Comparison of results granulomertic fractions contribution of wood sanding dust typically processed wood in the furniture industry (beech, oak, spruce, fir, and alder) was significantly confirmed of the particle size. Kategória publikačnej činnosti ADN Číslo archívnej kópie 38186 Kategória ohlasu MARTINKA, Jozef. Požiarne riziko materiálov. Bratislava : Vydavateľstvo Slovenskej technickej univerzity v Bratislave, 2018. 89 s. ISBN 978-80-227-4796-7.
DADO, Miroslav - MIKUŠOVÁ, Lucia - HNILICA, Richard. Laboratory investigations applied to wood dust emmited by electrical hand-held belt sander. In Management systems in production engineering. ISSN 2299-0461, 2018, vol. 26, no. 3, pp. 133-136.
KURACINA, Richard - SZABOVÁ, Zuzana - BALOG, Karol. Study of selected fire characteristics of beech wood depending on particle size. In Wood and fire safety : proceedings of the 9th international conference on wood and fire safety 2020, Štrbské pleso, 03th-06th May 2020. Cham : Springer, 2020. ISBN 978-3-030-41234-0, pp. 16-21.
PEDZIK, Marta - STUPER-SZABLEWSKA, Kinga - SYDOR, Maciej - ROGOZINSKI, Tomasz. Influence of grit size and wood species on the granularity of dust particles during sanding. In Applied sciences. ISSN 2076-3417, 2020, vol. 10, no. 22, pp. 1-9.
KUBOVSKÝ, Ivan - KRIŠTÁK, Ľuboš - SUJA, Juraj - GAJTANSKÁ, Milada - IGAZ, Rastislav - RUŽIAK, Ivan - REH, Roman. Optimization of parameters for the cutting of wood-based materials by a CO2 laser. In Applied sciences. ISSN 2076-3417, 2020, vol. 10, no. 22, pp. 1-16.
DADO, Miroslav - LAMPEROVÁ, Anna - KOTEK, Ľuboš - HNILICA, Richard. An evaluation of on-tool system for sanding dust collection : pilot study. In Management systems in production engineering. ISSN 2299-0461, 2020, vol. 28, no. 3, pp. 184-188.
ELAISSI, Arwa - ALIBI, Hamza - JABLI, Mahjoub - GHITH, Adel. Development of abrasives from non-woven based on used textiles. In Journal of natural fibers. ISSN 1544-0478, 2022, vol. 19, no. 6, pp. 2189-2203.
DADO, Miroslav - SALVA, Jozef - SCHWARZ, Marian - VANEK, Miroslav - BUSTIN, Lucia. Effect of grit size on airborne particle concentration and size distribution during oak wood sanding. In Applied sciences (Basel). ISSN 2076-34717, 2022, vol. 12, no. 15, pp. 1-14.
SATINOVA, Viktoria - HLAVAC, Pavol - IZDINSKY, Jan - REINPRECHT, Ladislav. Rot evaluation in spruce logs and rot reflection into dimensions of chips for particleboards. In Acta Facultatis xylologiae Zvolen. ISSN 1336-3824, 2022, vol. 64, no. 2, pp. 5-16.
PONPRATHOM, Yothin. Design and development of protective equipment from noise and dustof circular saws. In Advanced science journal. ISSN 1513-9980, 2022, vol. 22, no. 2, pp. R1-R20.
Katal.org. BB301 - Univerzitná knižnica Univerzity Mateja Bela v Banskej Bystrici Báza dát xpca - PUBLIKAČNÁ ČINNOSŤ Odkazy PERIODIKÁ-Súborný záznam periodika Názov Fyzikálne a aeromechanické vlastnosti piliny vznikajúcej v procese pílenia dreva na rámovej píle PRW-15M Súbež.n. The physical and aeromechanical properties of sawdust processed during the sawing process on the multi-blade frame saw PRW-15M Aut.údaje Martin Kučerka Autor Kučerka Martin 1980- (100%) UMBFP07 - Katedra techniky a technológií
Zdroj.dok. Acta Universitatis Matthiae Belii : séria: Technická výchova, No. 11. S. 19-29. - Banská Bystrica : Univerzita Mateja Bela, Fakulta prírodných vied, 2011 / Ďuriš Milan 1954- ; Čellárová Lýdia 1954- Kľúč.slová granulometrický rozbor dezintegrovaná drevná hmota piliny granulometric analysis sawdust Jazyk dok. slovenčina Krajina Slovenská republika Systematika 62 Anotácia Granulometrický rozbor a analýza tvaru a rozmerov častíc dezintegrovanej drevnej hmoty vzniknutých v procese pílenia je vykonaný na borovicovej piline vznikajúcej v procese pozdĺžneho pílenia borovicového reziva o vlhkosti w = 8,5 % na jemnorežúcej rámovej píle PRW – 15M, s reznou škárou 1,3 mm a pri rýchlosti posuvu materiálu do rezu v1 = 0,5 m.min-1 a pri rýchlosti posuvu v2 = 1,5 m.min-1. Výsledky granulometrického zloženia suchej borovicovej piliny vzniknutej v procese pozdĺžneho pílenia reziva na jemnorežúcich rámových pílach ukazujú, že borovicová pilina je tvorená z častíc s rozmermi od 84 μm do 15,2 mm. Z hľadiska tvaru zŕn sú hrubé frakcie suchej borovicovej piliny tvorené fibrilárnymi zrnami – tyčinkovitého tvaru. Stredne hrubá a jemná frakcia je tvorená v prevažnej miere izometrickými zrnami – tvaru kocky. Z porovnania kriviek zvyškov suchej borovicovej piliny s krivkami frakčnej odlúčivosti mechanických odlučovačov a filtrov plynie, že mechanické odlučovače typu T4/630, T3/1000 a T3/1600 a látkové filtre sú vhodné na odlučovanie piliny z porezu na jemnorežúcich rámových pílach PRW – 15M. This paper presents the results of granulometric analysis from desintegrated wood material processed during the sawing process is done on pine sawdust processing at the longitudinal sawing process of pine timber, with moisture content w = 8,5% on the multi – blade frame saw PRW – 15M, with width of kerf 1,3 mm and feed speeds v1 = 0,5 m.min-1, v2 = 1,5 m.min-1. Results of granulometric composition of dry pine sawdust processed during the longitudinal sawing process of timber on multi – blade frame saw show, that pine sawdust is created of particles with dimensions from 84 μm to 15,2 mm. From point of view of shape of grains, coarse fraction of dry pine sawdust is created by fibrilar grains. The medium coarse and fine fraction are mostly created by isometric grains – cube shape. From analysis of conditions of separation of dry pine sawdust in separators and filters results, that mechanical separators with elements T4/630, T3/1000 and T3/1600 and filters are convenient for separation of sawdust from sawing of wood on fine-sawing frame-saws PRW – 15M. Kategória publikačnej činnosti AED Číslo archívnej kópie 21714 Katal.org. BB301 - Univerzitná knižnica Univerzity Mateja Bela v Banskej Bystrici Báza dát xpca - PUBLIKAČNÁ ČINNOSŤ Názov Vplyv technicko-technologických faktorov na tvorbu triesky pri brúsení dreva na ručnej pásovej brúske Aut.údaje Martin Kučerka Autor Kučerka Martin 1980- (100%) UMBFP07 - Katedra techniky a technológií
Zdroj.dok. Acta Universitatis Matthiae Belii : séria Technická výchova, No. 10. S. 15-29. - Banská Bystrica : Univerzita Mateja Bela v Banskej Bystrici, 2010 / Ďuriš Milan 1954- Poznámka Bibl.: s. 29 Kľúč.slová granulometrická analýza technicko-technologické faktory ručné pásové brúsky granulometric analysis technical-technological factors hand belt grinding machine Jazyk dok. slovenčina Krajina Slovenská republika Anotácia Cieľom príspevku je zhodnotenie vplyvu technicko - technologických faktorov a modelu brúsenia, merného tlaku, zrnitosti a reznej rýchlosti na granulometrické zloženie drevného brúsneho prachu získaného z procesu brúsenia smreka na ručnej pásovej brúske GBS 100 AE, stanovenie objemovej hustoty drevného brúsneho prachu, granulometrická analýza drevného brúsneho prachu pri brúsení vybratej dreviny ručnou pásovou brúskou a vyhodnotenie získaných výsledkov z hľadiska modelu brúsenia, merného tlaku, zrnitosti a reznej rýchlosti. The results of this work is valorization influence of technical – technological factors and model of grinding, measuring pressure, granularity and cutting speed on granulometric composition of wood abrasion dust which was acquired from grinding process of spruce by using of hand belt grinding machine GBS 100 AE, determination of volumes densities of wood abrasion dust, granulometric analysis of wood abrasion dust, by the grinding of chosen wood plants on hand belt grinding machine and interpretation obtained results from aspects of model of grinding, measuring pressure, granularity and cutting speed Kategória publikačnej činnosti AED Číslo archívnej kópie 18079 Kategória ohlasu OČKAJOVÁ, Alena. Prašnosť v drevárskej prevádzke a jej možná redukcia. In Acta Universitatis Matthiae Belii : seria Technická výchova, no. 12. Banská Bystrica : Univerzita Mateja Bela, Fakulta prírodných vied, 2012. ISBN 978-80-557-0461-6, s. 67-73.
OČKAJOVÁ, Alena - BANSKI, Adrián. Granulometria drevného brúsneho prachu z úzko-pásovej brúsky. In Acta Facultatis Xylologiae Zvolen : vedecký časopis. ISSN 1336-3824, 2013, roč. 55, č. 1, s. 85-90.
BELJAKOVÁ, Annamária - OČKAJOVÁ, Alena. Drevina a model brúsenia ako faktory ovplyvňujúce podiel prachovej frakcie pri brúsení. In AFT: Acta Facultatis Technicae. - Zvolen : Technická univerzita vo Zvolene, 2005. ISBN 80-228-1517-9. ISSN 1336-4472, 2004, roč. 8, s. 169-177.
KMINIAK, Richard. Podiel prachovej frakcie v odsávaných trieskach z procesu frézovania dubového dreva na CNC obrábacom centre. In 37. stretnutie katedier Mechaniky tekutín a Termomechaniky : medzinárodná vedecká konferencia, Štúrovo, 27. - 30. jún 2018 [online]. Zvolen : Technická univerzita vo Zvolene, 2018, s. 145-149 [cit. 2018-11-16]. ISBN 978-80-228-3061-4. Dostupné na: https://kod.tuzvo.sk/sites/default/files/37_Stretnutie_katedier_1_0.pdf
BANSKI, Adrián - KMINIAK, Richard. Influence of the thickness of removed layer on granulometric composition of chips when milling oak blanks on the CNC machining center. In Trieskové a beztrieskové obrábanie dreva : vedecký časopis [online]. 2018, vol. 11, no. 1, pp. 23-30 [cit. 2018-11-16]. ISSN 1339-8350. Dostupné na: https://kod.tuzvo.sk/sites/default/files/banski_kminiak.pdf
KMINIAK, Richard - DZURENDA, Ladislav. Granulometric composition of chips from the milling process of spruce on a CNC machining center. In Annals of Warsaw University of Life Sciences - SGGW (Forestry and Wood Technology). ISSN 1898-5912, 2018, no. 104, pp. 48-52.
Katal.org. BB301 - Univerzitná knižnica Univerzity Mateja Bela v Banskej Bystrici Báza dát xpca - PUBLIKAČNÁ ČINNOSŤ Názov Metodika pre sitovú analýzu piliny z procesov pílenia dreva Aut.údaje Martin Kučerka Autor Kučerka Martin 1980- UMBFP07 - Katedra techniky a technológií
Zdroj.dok. Trieskové a beztrieskové obrábanie dreva 2008 : 6. medzinárodná vedecká konferencia. S. 155-159. - Zvolen : Technická univerzita vo Zvolene, 2008 Kľúč.slová pílenie piliny sitová analýza fraction sieving granulometric analysis microscopic analysis Jazyk dok. slovenčina Krajina Slovenská republika Systematika 674 621.93 Kategória publikačnej činnosti AFD Číslo archívnej kópie 9985 Kategória ohlasu KMINIAK, Richard - BANSKI, Adrián. Separation of exhausted chips from a CNC machining center in filter FR-SP 50/4 with finet PES 4 fabric. In 37th meeting of Departments of fluid mechanics and thermodynamics : AIP conference proceedings, Štúrovo, 27th - 30th June 2018. Melville : American institute of physics, 2018. ISBN 978-0-7354-1716-8, pp. 1-4.
Katal.org. BB301 - Univerzitná knižnica Univerzity Mateja Bela v Banskej Bystrici Báza dát xpca - PUBLIKAČNÁ ČINNOSŤ Názov Spracovanie a vyhodnotenie údajov sitovej analýzy v programe EXCEL 2000 Aut.údaje Martin Kučerka, Ján Šustek Autor Kučerka Martin 1980- (50%) UMBFP07 - Katedra techniky a technológií
Spoluautori Šustek Ján (50%)
Zdroj.dok. Trieskové a beztrieskové obrábanie dreva 2006. S. 179-184. - Zvolen : Vydavateľstvo Technickej univerzity, 2006 / Dzurenda Ladislav ; Banski Adrián ; Trieskové a beztrieskové obrábanie dreva 2006 medzinárodná vedecká konferencia Poznámka Bibl.: s. 184 Kľúč.slová program granulometrická analýza programme granulometric analysis output Jazyk dok. slovenčina Krajina Slovenská republika Systematika 631.571 Anotácia Res. angl. Kategória publikačnej činnosti AFD Číslo archívnej kópie 9644 Katal.org. BB301 - Univerzitná knižnica Univerzity Mateja Bela v Banskej Bystrici Báza dát xpca - PUBLIKAČNÁ ČINNOSŤ Názov Stanovenie hmotnosti jemnej frakcie v suchej smrekovej piline - technickým výpočtom Aut.údaje Adrián Banski, Vladimír Vacek, Martin Kučerka Autor Banski Adrián
Spoluautori Vacek Vladimír
Kučerka Martin 1980- UMBFP07 - Katedra techniky a technológií
Zdroj.dok. Trieskové a beztrieskové obrábanie dreva 2006. S. 13-17. - Zvolen : Vydavateľstvo Technickej univerzity, 2006 / Dzurenda Ladislav ; Banski Adrián ; Trieskové a beztrieskové obrábanie dreva 2006 medzinárodná vedecká konferencia Kľúč.slová granulometrická analýza technický výpočet granulometric analysis technical account Jazyk dok. slovenčina Krajina Slovenská republika Kategória publikačnej činnosti AFD Číslo archívnej kópie 9645 Kategória ohlasu DZURENDA, Ladislav. The influence of construction of sawing machines on the granularity of sawdust from the process of wood sawing. In Woodworking Technique : 3rd Internatinal Scientific Conference. Zagreb : Faculty of Forestry, 2009. ISBN 978-953-292-009-3, s. 129-141.
OČKAJOVÁ, Alena - BELJAKOVÁ, Annamária - SIKLIENKA, Mikuláš. Morphology of dust particles from the sanding process of the chosen tree species. In Wood research. ISSN 1336-4561, 2010, vol. 55, no. 2, pp. 89-98.
DZURENDA, Ladislav. Štruktúra zrnitosti a podiel izometrických triesok v mokrej piline z procesov pílenia dreva na hlavných piliarskych strojoch. In Acta Facultatis Xylologiae. ISSN 1336-3824, 2009, vol. 51, no. 1, pp. 55-56.
OČKAJOVÁ, Alena - BELJAKOVÁ, Annamária - LUPTÁKOVÁ, Jana. Selected properties of spruce dust generated from sanding operations. In Drvna industrija : znanstveno-stručni časopis za pitanja drvne tehnologije. ISSN 0012-6772, 2008, vol. 59, no. 1, pp. 3-10.
Katal.org. BB301 - Univerzitná knižnica Univerzity Mateja Bela v Banskej Bystrici Báza dát xpca - PUBLIKAČNÁ ČINNOSŤ Názov Effectiveness of separation of wet pine sawdust in mechanical separators of type SEB with elements T4/630 Aut.údaje Ladislav Dzurenda, Martin Kučerka Autor Dzurenda Ladislav (50%)
Spoluautori Kučerka Martin 1980- (50%) UMBFP04 - Katedra životného prostredia
Zdroj.dok. 1 st Jubilee Scientific Conference : manufacturing Engineering in Time of Information Society. S. 99-104. - Gdansk : Politechnika Gdansk, 2006 Kľúč.slová granulometrická analýza granulometric analysis pine sawdust mechanical separators Jazyk dok. angličtina Krajina Poľsko Systematika 621.931 Kategória publikačnej činnosti AFC Číslo archívnej kópie 9648 Kategória ohlasu OČKAJOVÁ, Alena - BELJAKOVÁ, Annamária - SIKLIENKA, Mikuláš. Morphology of dust particles from the sanding process of the chosen tree species. In Wood research. ISSN 1336-4561, 2010, vol. 55, no. 2, pp. 89-98.
Katal.org. BB301 - Univerzitná knižnica Univerzity Mateja Bela v Banskej Bystrici Báza dát xpca - PUBLIKAČNÁ ČINNOSŤ